[slinkelist] How do I get Slinke to echo IR to the remote-IR box

[Saleh W. Igal]

If it still isn't working, make sure you are using an RJ-11 cable that is
wired straight through, NOT flipped like most telephone cables.  I ended up
just rewiring my IR transmitter module so I could use any of the flipped
RJ-11 cables I had on hand.
----- Original Message -----
From: "Hunt, Ed" <ed.hunt@attws.com>
To: <slinkelist@nirvis.com>
Sent: Tuesday, April 18, 2000 4:18 pm
Subject: RE: [slinkelist] How do I get Slinke to echo IR to the remote-IR
box


> Thanks for the replies from Colby, Peter and Ron.
>
> I ran SlinkeServ and tried echoing port 0 to port 7 and various
combinations
> of port configurations and wrote them to RAM and EEPROM each time but at
no
> time could I seem to get it to work.
>
> I'm using the remote that came with my CDP-CX240 and can see the Sony
> commands received when I run CDJ, so I know the port 0 receiver is working
> on the Slinke box.  How is that remote IR box wired, please?  I could pry
it
> open and check the wiring.

>
> Any more ideas?
>
> Ed Hunt
> TPS, Technology Development Group
> AT&T Wireless Services
> ed.hunt@attws.com
> 425 580 6743
>
> > ----------
> > From: Ron Chrisley[SMTP:ron@chrisley.freeserve.co.uk]
> > Sent: Monday, April 17, 2000 8:50 AM
> > To: Hunt, Ed; slinkelist@nirvis.com
> > Subject: Re: [slinkelist] How do I get Slinke to echo IR to the
> > remote-IR box
> >
> > I'm no expert, but I think you have to configure Slink-e to echo by
> > setting
> > the firmware.  I've done it via the PC; I don't know how to do so
> > otherwise.
> > From the help file:
> >
> > Setting up the IR ports to echo commands into other rooms
> >
> > The Slink-e has a handy feature which allows you to "echo" the commands
> > picked up by the receiver module in one room to the transmitter modules
in
> > other locations. The Slink-e is very flexible in terms of which
receivers
> > get echoed to which transmitters, and you must set up the Slink-e to
> > specify
> > these settings. Using SLINKSERV.EXE, go to the View->Slink-es->Settings
> > dialog. In this dialog there is a cross-point matrix of blue lines which
> > specify which receiver inputs (on the left) go to which transmitter
> > outputs
> > (on the top). By clicking on any of the line intersections you can turn
> > "on"
> > (a red dot) or "off" (no red dot) the connection between a given
receiver
> > and transmitter. Each receiver can go to any / all of the 8
transmitters.
> > For each receiver you must also specify the carrier frequency of the
> > remotes
> > you are using, since the receiver module does not pass this information
on
> > to the Slink-e. The choose a default of 40000Hz if you are not sure.
> >
> >
> > ----- Original Message -----
> > From: Hunt, Ed <ed.hunt@attws.com>
> > To: <slinkelist@nirvis.com>
> > Sent: Monday, April 17, 2000 5:39 AM
> > Subject: [slinkelist] How do I get Slinke to echo IR to the remote-IR
box
> >
> >
> > > Folks,
> > > I've now put my two CDP-CX240s into a cabinet with a wooden door with
> > the
> > > Slinke unit on top, quite discreetly.  I'd like to use the IR echo
> > function,
> > > as I believe this works even without a PC, so I plugged the RJ-11
cable
> > into
> > > the Slinke and placed the small phone-jack-box-IR unit that came with
> > the
> > > Slinke inside the cabinet door.  However I don't seem to get any
> > > transmission out of that unit.  It's not to do with position, because
> > I've
> > > tried holding the box three feet away with the door open using the
Sony
> > > remote near the Slinke so that there was no direct IR signal into the
> > > cabinet.
> > >
> > > When I run CDJ I can see that it is receiving Sony IR signals, but I
> > don't
> > > have CDJ programmed to do anything with them.
> > >
> > > Am I missing something?
> > >
> > > Thanks
> > >
> > > Ed Hunt
> > > ed.hunt@attws.com
> > >
> > >
> > >
> >
> >
> >
> > _______________________________________________
> > slinkelist maillist  -  slinkelist@nirvis.com
> > http://www.nirvis.com/mailman/listinfo/slinkelist
> >
>
>
> _______________________________________________
> slinkelist maillist  -  slinkelist@nirvis.com
> http://www.nirvis.com/mailman/listinfo/slinkelist


__________________________________________________
Do You Yahoo!?
Talk to your friends online with Yahoo! Messenger.
http://im.yahoo.com